woundskate2

Fiat 500 Replacement Key Fob If your 500 remote key fob has stopped functioning, it could be time to replace the battery. If you replace the battery but it's still not working it could be a problem elsewhere. At United Locksmith, we specialize in the creation of new keys for old cars. We have the tools as well as the parts needed for this job. Dead Coin Battery The most common reason your Fiat 500 key fob will not unlock or lock the doors is a dead battery. The coin cell battery in the key fob will deplete quickly when you don't utilize frequently enough. If your remote starts to show signs of loss of range or has stopped functioning, then the battery may be dead. The battery inside the key fob is held in place with metal clips for retaining. If the clips aren't tightly secured, they could result in contact issues that prevent your remote from receiving power. Use a flathead screwdriver to break open the retaining clip and then remove the old battery. Use a battery that has the same size, voltage and specifications as the original. The key fob may also become corroded or damaged by exposure to water. Even a quick bath in soapy water can cause damage to the electronic chip inside. Make sure your key fob is dry. Water Damage If your key fob isn't functioning properly, it could be due to water damage. The rubber seals on key fobs prevent them from getting damaged by a small splash or drizzle of water. However, it's essential to keep the keys of your car away from the washing machine, ocean, and pool. The key fob comes with an electronic chip that transmits an alert to the immobilizer of your car. This is the reason why your 500 can start or lock, however if the chip gets wet, it will no longer work. If you're trying to determine if your key fob is still functioning, you can clean the internal electronics with isopropyl or an electronic cleaner. It is recommended to replace a key fob in the event that it has been submerged into salt water, rather than trying to fix it yourself. While a replacement fob can cost you a bit of money, it's far less expensive than paying for your Fiat 500 to be towed to the dealer and repaired! You could also do it yourself by following some simple steps. Just ensure you have the correct battery type before you attempt to open your key fob. You can find step-bystep instructions for any car keyfob on the internet. Faulty Chip The chip inside the key fob communicates with the car's immobiliser unit to ensure the car is capable of starting when the correct key is used. If the chip is damaged or damaged in any way the car won't start. Damage to the water or a dead battery are the most frequently cited reasons for the chip being damaged. It is best to delegate the repair to a professional locksmith, who can replace the chip in a short time and at a an affordable cost. If your key fob stops working after exposure to clean water from the tap or rain, take out the battery and wipe down the electronic component with a tissue to ensure it's dry before putting it back in. If the key fob will not work, there is the possibility that it has a fried component and needs to be replaced. Some people go to their dealer if they require a new Fiat fob. However, Highly recommended Site can be costly. United Locksmith is the best option for you if would like to have your Fiat key fob repaired at a reasonable price. We have the tools and experience needed to repair your Fiat key fob in a timely and professional way. Faulty Receiver Module Fiat key fobs send signals up to 50 feet to the vehicle, which allows it to unlock and close the doors (and start the vehicle in case of automatic transmissions). There are many reasons why a fob could stop working. These include a dead coin battery water damage buttons, worn out buttons, a receiver module issue, and signal interference or an electronic chip that has failed. If the fob has been in a pocket which has suffered a severe trauma, such as being dropped on hard floor or getting washed in a wash machine the fob may not be capable of communicating with the car's Body Control Module (BCM). This is because the BCM is an extremely secure system that will only accept signals from a genuine original key and not another. It is necessary to replace the fob in case this occurs. A professional locksmith can take care of all aspects of the key replacement procedure as well as programming a new one for your 500. They can even offer the fob cloned to work exactly like the original (and costs just a fraction of the price).